Übersetzung für "Zu niedrige werte" in Englisch

Too high or too low pH values have a negative effect on the rhodium recovery.

This can simulate vitamin B12 values which are too low.

Whether casting defects do influence the quality of the end product and if so to what extent, is ultimately dependent upon a number of metallurgical and technological factors, the significance of which is not always grasped from the outset.

The high values become low values and low values become high values.

They often have too small stimuli, which result in too low values.

The corresponding MLC displays have values for the resistivity which are too low for some commercial applications

The corresponding MLC displays have values for the resistivity which are too low for some commercial applications

Unduly high pH values prolong the reaction time, whereas unduly low pH values are disadvantageous under various aspects.

Excessively low values for the total pressure per cycle often lead to blue-colored teats.

Your blood sugar levels may become too high or too low (see ‘ Low blood sugar’ in Section 4).

You may be at risk of having low blood sugar and need hospital treatment.

For example water can negatively interfere with a CLD's NOx response through collisional quenching and can positively interfere with an NDIR analyser by causing a response similar to CO;

H2O and CO2 can negatively interfere with a CLD's NOx response by collisional quenching, which inhibits the chemiluminescent reaction that a CLD utilizes to detect NOx.

A portion of the phosphoric acid can also be added as KH2 PO4, if too low a pH is attained by the acid alone.

Some industries are highly labour intensive and so will have low labour productivity figures when compared with more capital intensive industries.

Resins without a gel structure have a substantially viscous behavior and show high G" values, whereas G', in comparison with G", gives relatively low values.

A portion of the phosphoric acid can also be added as KH2 PO4, if too low a pH is attained by the acid alone.

Here too, the W.P. increases strongly at higher contents, while a20/300 adopts values which are too low.

This ensures, in the case of every cylinder, that the noise value GW represents the noise behavior of the cylinder without assuming excessively high or excessively low values, i.e. both the noise value GW and the knock threshold KS dependent on it assume practical values, even if there is an assumed relation of high knock values KW.

If only the complete, undegraded peptide is recognised in the assay method, values which are too low are therefore obtained.

Excessive pH-values extend the reaction time, whilst inadequate pH-values are disadvantageous from several standpoints, e.g. can lead to an at least slightly undesired dissolving of the precipitated, cationizable melamine/formaldehyde precondensate.

The forced change-over stage becomes operative in the case in which the current through the load assumes excessively low values, for example in the case of a defect or a current interruption in the load.

The measurement values set out in Table 3 show that without the addition of detergent to the diluted samples, too low HDL cholesterol values are found and that the addition of a detergent is able to overcome these errors.

It is known that such prediluted samples, after precipitation of the apo-B-containing lipoproteins, give too low values for the HDL-cholesterol.

On 74 % of the arable land the soil pH is either too high or too low which in turn causes yield losses and reduces soil fertility.

To high LDL values and to low HDL values are primarily a reference to lack of movement and error feeding.

Below 1% by weight the effect of component (B) is slight, and the advantages of component (B) have little effect in the moulding compositions; above 15% by weight there is a sharp decrease of stiffness and the moulding composition is no longer adequately processable because of excessive melt viscosity (excessively low MVR values).

Below 10 wt %, the effect of component (b) is small, and so the advantages of component (b) are hardly felt in the moulding compositions; above 40 wt %, the stiffness reduces greatly and, on account of an excessive melt viscosity (excessively low MVR values), the moulding composition can no longer be adequately processed.