Übersetzung für "Starker abfall" in Englisch

Alternatively the decrease in the latex viscosity during the agglomeration can be monitored.

For example as the Curie temperature is reached, the magnetic field will drop sharply.

A short term strong decrease of the oil pressure thus leads to a reduced compression.

A sharp drop in viscosity is characteristic of the phase inversion.

Is there a large decrease in a single stat?

Reclay Slovensko, s.r.o. is your strong partner for waste and packaging management.

A sharp decline compared to the 243 victims surveyed in December.

In the case of constant current cycling operations with high current stresses, a significant decline in capacity occurs after a few cycles.

Signs of these reactions are: a sharp drop in blood pressure, paleness, restlessness, weak/ rapid pulse, clammy skin, dizziness.

Allergic reactions such as sudden fall in blood pressure or anaphylactic shock (a sharp fall in blood pressure with other symptoms such as swelling of the throat, breathing difficulties and skin rash) are rare but they can occasionally occur even if you have not previously had problems with similar treatments.

Uncommon: Heart failure (signs include shortness of breath, chest pain, swelling of the legs due to fluid build-up), severe problem with the rate or rhythm of the heart beat (ventricular tachycardia, supraventricular tacycardia or atrial fibrillation), inflammation of the pancreas which causes severe abdominal and back pain (pancreatitis), vomiting blood or passing bloody or black stools, severe reduction in blood cells which can cause weakness, bruising, bleeding or infections (pancytopenia).

Too great a drop in pH into the acid region can be avoided by adding an organic or inorganic base, preferably CaCO3.

Too great a drop in pH into the acid region can be avoided by adding an organic or inorganic base, preferably CaCO3.

Even in pure polypropylene films, for example, a considerable decrease of volume resistivity occurred already at a temperature of about 70° C., whereas in the films according to the invention, such a decrease was not observed until a temperature of about 100° C. was reached.

When high concentrations of fluorescent whitening agent are used there often occurs a sharp decrease, instead of an increase, in the degree of whiteness, and the coating composition often also takes on a greenish hue.

The maximum extends over a temperature range from 20°-50° C. and after the maximum has been exceeded, a very strong drop in the density values is observed.

The maximum extends over a temperature range from 20°-50° C. and after the maximum has been exceeded, a very strong drop in the density values is observed.

Too great a decrease of the pH into the acid range can be prevented by the addition of an organic or inorganic base, preferably CaCO3.

Too great a drop in pH in the acid range can be avoided by adding an organic or inorganic base, preferably CaCO3.

Whereas in the case of agglomerated molding powders of tetrafluoroethylene, ie. those containing no modifying agent, a considerable decrease in the pore count, compared with the finely ground starting powder, takes place as an undesirable consequence of the agglomeration process, this is the case only to a very small extent in the agglomeration leading to the modified molding powders according to the invention.

After the voltage rise, a steep drop of the shunt resistance RQ between the closely adjacent parts of the anode is observed.

As can be seen from FIG. 8b, a fresh severe decrease in the signal activity then occurs which in turn depends strongly on the material of the vessel used.

An unacceptably large decrease in pH into the acid range can be avoided by addition of an organic or inorganic base, preferably CaCO 3 .

A sharp drop in heart output results in the body being inadequately supplied with blood, which finally can result in death.

While the temperature decrease for GX 1657 with saturated middle block is almost linear with increasing active ingredient content, in the case of TR 1107, when the bupranolol content goes above 10 weight %, surprisingly a large drop is observed.

Although ABS molding materials prepared in this way have a certain matt effect, at the same time a sharp drop is observed in the multiaxial toughness and other mechanical properties.

The first child precipitates a sharp fall in activity rate, followed by a steady decline as family size increases.

An extensive reduction is observed in transmission values as well as in notch impact resistance, which greatly restricts the possibilities of utilization.

Too great a drop of the pH value into the acid range can be compensated by additions of bases, for example NaOH or CaCO3.