Übersetzung für "Leicht verbogen" in Englisch

The protruding tongue 8 of the aluminum profile can easily be bent during transport.

It can very easily become bent or broken during the handling of the sample.

It has been slightly bent so that it forms a small ball.

If the wire is only slightly bent, the current is reduced.

Moreover, if the leaf spring 57 is fitted or removed incorrectly, it is easily bent or broken off.

They can easily be bent elastically on the slide bush 3 towards the latter?s outside wall 15 .

The base plate 52 of the first attachment member 48 is bent slightly along the bending axis 113 .

In sewing machines, it is encountered time and again that the needle is slightly deviated from its initial course or bent during its penetration into the material being sewn when the material is advanced in any direction along the sewing plane during the time that the needle passes into and/or beyond such material.

Motor-driven hand operated extruding devices with a worm drive for the piston have the disadvantage that the piston rod extends out of the drive housing when the piston is retracted and the rod can easily be bent due to rough handling.

Particularly if the diameters of the two pipe ends are unequal, which is the case, for example, in all kinds of very frequently used insertion-type pipe connections, or if the pipe ends are improperly cut, slightly deformed or damaged, it is even more difficult to apply the coupling sleeve to the pipe ends in such a way that these ends will be sealed uniformly against the sleeve and also that an inward projection will not be formed at the packing strips inside the coupling sleeve.

In addition to the relatively complex structure, another disadvantage of the known transformer consists of the fact that the assembly of the transformer-winding unit, on the one hand, and the part comprised of the cap and the walls, on the other hand, is difficult, since many points of the winding unit must be correctly positioned opposite the corresponding points of the part consisting of cap and walls prior to joining and the walls can be easily mechanically bent relative to one another.

Due to internal stresses between thin layer 2 and flexible beam 11, flexible beam 11 is bent slightly upward.

The rotor shaft, for example, is often only as thick as a knitting needle, and can therefore easily be bent if handled carelessly, rendering the fan unusable.

In general, the whole area is slightly bent and forming a basin centered in the Tone River and Tokyo Bay.

The string lighting can be easily bended, and shaped around christmas trees, signs, furniture and almost everything else.

Condition: One applique especially on the torch slightly bent, otherwise both intact except for some corrosion traces.

In the case of this previously described safety guard mount, this arrangement has proved to be disadvantageous because the comparatively fragile S-shaped spring element can be easily damaged or bent out of shape when the safety guard is being released and removed from the spindle neck.

In that case the arrangement of the grooves is so selected that the ball cage is slightly bent upon fixing transversely with respect to its longitudinal axis and by virtue of its flexibility or elasticity always urges the balls with a prestressing against the running surface of the guide rail.

It is apparent in particular that the incisions 7 define tongues 8, which are easy to bend, such that the housing may be simply adapted to the geometry of the wheelset axle, which is generally thicker in its end region, at which the wheels are mounted.

In one advantageous refinement, the actuating stud has a rotationally symmetrical basic shape, with the result that it can be easily bent in any direction perpendicular to its main axis in order to compensate angular deviations during the action on the snap-action disk.

Such a substantially plate-shaped secondary core can be easily deformed, in particular bent or broken through, in the x-direction in the event of a collision, and requires little installation space between the bumper and the passenger compartment, so that foam deformation elements to be mounted in this area which is important for the frontal crash performance can have a greater thickness, i.e. dimension in the direction of travel.

Such essentially plate-shaped secondary transformer unit can be easily deformed in a collision in the x-direction, in particular bent or broken through, and requires little installation space between the bumper and the passenger compartment, so that foam deformation elements to be installed in this region that is important for crash behavior may have a greater thickness.

Above the hook 7, a positioning device 11 is shown above the hook 7, which, guided by the needle 3, also positions the hook 7 in the lateral direction precisely in front of the eye 5, regardless of the needle thickness or the fact if the needle 3 is perfectly straight or slightly bent.

Furthermore, there is a danger that the snap-in elements are slightly bent in response to an inappropriate insertion of the reservoir so that either the snap-in position is canceled or the snap-in pins are disposed perpendicular to the upper side of the flange so that, due to the upward movement of the metering valve, the displacement of the snap-in pins can no longer be realized.

The fingers are relatively narrow and can therefore easily become bent so that the measuring precision is impaired.

A complication additionally arises that the stuffing tubes can be bent easily, in particular long stuffing tubes with small diameters.

Clamping the second oscillator in at one end on the first oscillator has the advantage that, when an electrostatic force is exerted on the second oscillator as a result of the alignment/position change of the second oscillator, the second spring elements can be slightly curved, thus making it possible, without any problems, to vary the corresponding alignment angle of the second spring elements.

In this connection, the result is achieved, in simple and price-advantageous manner, that the cooling channel cover is built into the piston so that it absolutely cannot rotate, in that a tongue is punched into the radially linear region of a cooling channel cover in the form of a disk spring, and this tongue is slightly bent, so that it can engage into a recess formed into the outside of the piston.

Especially as transverse forces are applied to the fingers, as they can, for example, be produced when a stone gets between a sickle blade and a counter cutting edge, the double finger can be easily bent.

However, in this case the danger still exists, that when transverse forces are produced, the fingers of the upper element, especially, in the area of the blade gap, can be easily bent.