Übersetzung für "Spannung vorhanden" in Englisch

In most cases, there is a two-dimensional tangential stress.

No voltage will be present at the output.

Electrical fields form wherever there is voltage.

Several sockets with different or same voltage can be available, for example.

Verify the presence of voltage!

Only if there is no voltage drop in both cases, a combination of the two-ports networks is permissible.

There is still enough energy in the rock, so that more are predicted to follow.

At least one further short-circuit path for short-circuiting the voltage between the bus lines is present.

It goes without saying that a hazardously high voltage can also be present in the device 3 itself.

Upon startup of a fan motor 20, no induced voltage is present when the motor is at a standstill.

If there is excess voltage, the barley with blanched vegetables helps to relax.

One should get accustomed to such summons when there is so much tension everywhere.

Detect The Presence Or Absence Of Voltage! The Model 7929 AC Sensor provides non-contact verification that a voltage is present.

If necessary, maintenance of the proper temperature of the roll electrode may be improved by using the electrode in combination with steel or rubber rolls of an adjustable or controllable temperature, as indicated in FIG. 1 by rolls 13. This is possible due to the absence of any electrical voltage in the contact area.

Altogether the list shows clearly that practically any fault which could impair the operation of the machine is detected; generally this will be indicated by the red control lamp LP4 except in the cases where there is no voltage or where no voltage is connected through. In these cases, however, there is no danger that the machine will start or continue to run and as a result no faults can occur which could endanger machine or tools.

The feed module comprises a lamp 94 indicating whether an electric voltage is present on the primary side of the voltage generator 14.

This is aim the case on the lead 25b, be it shifted through one phase, so that the voltage 3U is continuously present, via the diodes D18 and D28, on the lead 15 for the positive supply voltage VDD, notably when the charging capacitance CL connected to the lead 15 in FIG.

It is then evident from the lighted color that voltage is present and which voltage is present, namely one suitable for operating the power pack or one which is unsuitable for operating the power pack.

This said electric circuit comprises means for smoothing the voltage being storage elements at the same time, hence chokes and condensers.

Decoder according to claim 10, wherein said substitute voltage source (U4, U5) corresponds to a voltage which tunes the oscillator (5) as if a voltage value (U1, U2) were present.

The control circuit 37, for example provides current to light the lamp 38 when the input stage is not proper for the voltage of the supply line.

In such a case, however, a certain voltage should be present at the output of the power supply unit, which voltage should correspond to a setting for transmission of the unmodulated carrier frequency.

The corresponding division significantly facilitates the characterization of the product, because it makes it possible to begin from the alternative that at an observed reference point there is either an electrical field differing from zero, with imperceptible mechanical tension, or an imperceptible electrical field with mechanical tension differing from zero.

Then a LOW signal must be present at the driver output terminal 20, whereas suppose driver input terminal 16 is HIGH at +5V.

Also, the evaluation of pulse-shaped signals can be used for improving the safety of the whole system, since in this situation not only voltage must be provided, which eventually can also occur as disturbance, but also the signal must have the correct frequency.

When a high voltage is present between the electrodes 154 and 156, the resultant electrostatic fields effectively "pin" the segment of the belt loop 10 that is wrapped around roller 150 to the surface of the roller thereby minimizing or preventing relative slippage of the belt loop relative the roller.

Thus it is safeguarded that power relay 4 will only stay in its switched-in position as long as the three phase AC voltage is supplied via the cable 1 to all three phases A, B and C of the AC power system on board.

In addition, a tension or pull armature shank 74 of electromagnet 26 engages through an opening 75 of the hinged armature plate 73 and grips behind the same, so that electromagnet 26 acts both with a pull armature 74 and a hinged armature and consequently there is a high holding power compared with the voltage to be used.

If both switches 10 and 11 are open, no voltage appears across the resistor 6, and if the EO modulator has the characteristic shown in FIG. 5c, which can be obtained with, for example, liquid crystals, the transmission will be at a point A on the curve in FIG. 5c.