Übersetzung für "Metrische gewinde" in Englisch

50CM Metric Thread Rod (Select Diameter)

However, other screw thread types, for example metric screw threads etc., are also imaginable.

The screw cap B provides optimum protection for metric and imperial threads.

Metric threads available (add metric thread size to the end of catalog number)

In Germany, general mechanical engineering makes use of metric ISO threads in accordance with DIN 13.

The ISO Metric Coarse Thread DIN 13-1 is a globally standardized thread profile.

A bolt, for example an eye bolt, can be screwed into the metric thread.

According to one embodiment of the present invention, the threads 42 and 52 are metric threads matched to each other.

However, female threads, such as metric threads or Whitworth threads, have proved especially useful.

This metric screw thread of the traction pin constitutes a screw connection with the inner thread of a nut, elongation screw or similar, the inner surface of the nut, the elongation screw head or similar directed perpendicularly to the longitudinal bolt axis, acting directly or indirectly as abutting surface for the actuator member of the hydraulic jack.

The inner thread 10 of the locking element 8 and the outer thread 16 of the inner screw are constructed in these embodiments in each case as metric threads.

Relative to the approximately 100 screw and bolt manufacturers in the Federal Republic, SP maintains its position primarily through its wide range of products (DIN parts, metric threads, trapezoidal threads, etc.).

Sheet-metal nuts having other common thread configurations up to the threaded bush for metric threads can also be used, it being possible in the latter case for the threaded bush to protrude slightly above the upper edges 8 of guide webs 7.

Extensive accessories, metric threads in the housing and its very small size enable fast integration even under difficult installation conditions.

Thread rolling, also after the heat treating of 12.9 (metric threads, UN, UNC, UNF, Withworth, or according to the client's drawings). By rolling we achieve an improvement of mechanical properties due to the course of force lines with regard to the thread form, a cold solidification of the surface, a decrease of surface roughness and the resulting decrease of the friction coefficient.

Metric threads available in sizes from 300kg to 13,000kg and dual rated in4 to 1 design factor.

This is not a direct cross to the John Deere Part No. John Deere uses metric threads and this nut is 3/8" threads.

The metric ISO thread is manufactured to the tolerance class "fine" (tolerance class 5H, DIN 13, parts 21- 25) in a single work process with the end face of the locknut.

The metric ISO thread is manufactured to the tolerance class "fine" (tolerance dass 5H, DIN 13, parts 21- 25) in a single work process with the end face of the locknut.

From the side opposite the tube 1 an inflation adapter 20 is screwed into the casing-like sleeve 7 into the metric thread which is located there in the section 14 and is sealed relative to the sleeve 7 by ring packing (O-ring) 21 .

It is preferable in this connection if the thread for holding the casings which are joined to the expandable tubes of the friction tube anchors are round threads, and threads for holding inflation adapters or other components such as bolts are metric threads.

In this embodiment the pressurized fluid which is necessary for expanding the expandable tube is fed via the inflation adapter which has been screwed into the metric thread of the sleeve (hanger jacket).

Because the diameter of the locking element 3 in the first anchoring section 4 is smaller than in the locking section 7, the locking element 3 can be initially passed with its first end 11 through the transverse duct 4, without the bone-screw thread in the first anchoring section 6 and the metric thread in the transverse duct 4 causing damage to one another.

In the locking process between the locking element 3 and the nail 2, the pin section is pressed against the metric thread, which is arranged in the transverse duct 4 .

By this metric thread, a fastening torque can be defined particularly well, and the lead of the thread can be determined in such a way that the locking between the nail and the locking element is as safe as possible.

The positively locking connection between the rudder blade axis member 36 and the rudder blade foot 14 can be embodied for example by metric screwthreads 48, 68, by trapezoidal screwthreads or by suitably shaped depressions and raised portions, involving one or more pitch flights.

Metric threads are a further important component: metric threaded rods from which screws of any length can be produced.

In metric dominated continental Europe and in some parts of Asia metric threads could be built in as well.

These laser modules were created for application in the industrial environment: The metric ISO M12 thread was integrated in the stainless steel housing of the laser.