Übersetzung für "Vollflächige verklebung" in Englisch

Full spread gluing is also advisable if different widths are combined.

In addition, full-area bonding of the mounting part may be provided on the component.

The domes, deformed by the applied pressure, form a whole-area bond.

With other products, full spread gluing is a must.

Excellent adhesion due to the entire surface of the gluing means that no dirt or dirt accumulates under the foil.

The fact that skis shall, on the one hand, show torsion stiffness and, on the other hand, shall also show bending elasticity results in differing requirements with respect to the load carrying capacity of the composite construction along different axes, and a full-areal glueing of individual layers as in present multilayer skis is, when it is intended to reliably provide for a corresponding torsion stiffness, are unsuitable to attenuate vibrations, in particular transversal vibrations. SUMMARY OF THE INVENTION

The invention is based on the knowledge that a joining of hollow chamber panels into a stack is considerably simpler and cheaper to produce if the hollow chamber panels are joined only in the area of the front surfaces with the adjacent hollow chamber panels than if total surface gluing of the wall surfaces is performed, yet a heat exchanger body joined in this way has no technical disadvantages.

Composite panels are known in which metallic or nonmetallic cover strips are bonded to core layers, predominantly of inorganic nature, by bonding over the full surface with the aid of a binder.

By use of large area, visco-elastic bonding of the core to the outer layer a high resistance to delamination, slackening due to vibration, corrosion and moisture is achieved.

In order to achieve, as far as possible, a full-area bond, the applied pressure on the adhesive strip is mediated by a 10 mm thick foam interlayer (PU foam of density 100 kg/m 3).

Here they then prevent adhesion or melting over the whole area of the two halves of the valve tube laid flat under pressure after reactivation of the inner layer.

Because the fabric cloth 2 and the plastics film 3 are thermally bonded or are connected to one another via the self-adhesive tape only at two edges, i.e. at their narrow sides, and in the latter case there is no adhesive bonding over the entire surface, there is also no danger that the cleaning liquid applied to the fabric cloth might attack and dissolve the adhesive.

The invention is based on the knowledge that a joining of hollow chamber panels into a stack is considerably simpler and cheaper to produce if the hollow chamber panels are joined only in the area of the front surfaces with the adjacent hollow chamber panels than if total surface gluing of the wall surfaces is performed, yet a heat exchanger body joined in this way has no technical disadvantages.

Please note that a glue-down installation of DISANO products is only possible with the variants DISANO Saphir, DISANO Classic (with Aqua Shield treatment), DISANO Classic Aqua, DISANO Smart Aqua and DISANO Project.

If you want to install the Villa by Adler 35 wooden plank on an underfloor heating system, we always recommend installation with total glue down on your floor screed.

The main focus was the innovative compacore® process from voestalpine Automotive Components Nagold that uses full-faced inline bonding of high-quality electrical steel to produce rotor and stator packages for electric motors with guaranteed mechanical and electromagnetic properties.

To avoid an all-over bonding, there must be employed an adhesive that does not yet cause bonding upon a contact of the two security-element partial elements as is necessary for irradiation.

The exterior shells 3, 4 and the core 2 are combined through a full bonding, in order to form a self-supporting unit.

Full-area bonding, in the case of an approximately central disposition of the electronic structure, in contrast to edge sealing, offers the advantage that the permeant would have to diffuse through the entire area before reaching the structure.

Full-area bonding is hard to achieve, owing to the contraction that occurs as a result of curing, since in the course of curing there are stresses between adhesive and substrate that may in turn lead to delamination.

In particular, this process allows the realization in a very simple manner of the long held desire for full surface, long-term adhesion of a PVC strip to a substrate, in particular a roof or a roof structure, and thus to obtain optimal sealing.

The composition is used preferably as wood flooring adhesive, as for example for solid wood flooring, plank wood flooring (tongue and groove), laminate wood flooring, industrial wood flooring, boards, mosaic wood flooring, wood tiles, and wood chipboard panels, preferably for full-area adhesive bonding.

In principle, however, a substantially full-surface adhesion of the common contact surfaces is also possible in that the adhesive is applied by brushing onto the layer(s) or that the layer, particularly the reinforcement layer, is dipped into the adhesive.

According to the invention, the adhesive is applied here such that a substantially full-surface adhesion of the common contact surfaces is produced during the subsequent bonding of the reinforcement layer with the further layer.

During the connecting or pressing procedure, the adhesion-preventing material, by the formation of a liquid layer at a relatively high softening or melting point in the region of the partial region to be subsequently removed will prevent a continuous connection, for instance adhesion or connection of the mutually adjoining material layers or material layers to be connected, as is desired or sought in regions adjoining the partial region to be subsequently removed.

For this, the film tube is used together with the textile tube and a preferred embodiment may provide that the textile tube is laminated with the film tube, laminated to be understood as meaning a partial or full-areal adhesive bonding together of two sheets.