Übersetzung für "Set point temperature" in Deutsch

This maximum allowable temperature is above the set-point temperature by an allowable temperature deviation.

This value is subsequently transferred to the heating element control as a reference value corresponding to a set point temperature.

This allows data center managers to raise the supply air set point temperature and reduce cooling unit fan speeds.

The lower the set-point temperature selected, the lower the cooling capacity.

The lowermost switch has two settings which control the set point temperature for dialysate solution heating.

The set-point temperature of the water drawn for the coal gasification process is thus attained by decoupling heat from the high-pressure stage, having evaporator heating surfaces in which sufficient heat is generated.

In this process the temperature of the partial quantity a is increased by absorbing heat generated in the evaporator 36, so that by suitable adjustment of the three-way valve 48, a mixed temperature corresponding to the set-point temperature is established on the downstream side of the valve 48.

To that end, a partial quantity a' of the drawn water, which is carried to a loop 51', is altered by indirect heat exchange with the water of the water-steam drum 34, in such a way that by mixing the drawn water with the partial quantity a', with suitable adjustment of the valve 48, the set-point temperature is established in the line 46 on the downstream side of the valve 48.

Depending upon how much heat is withdrawn by the heat consumer 2, the supply temperature measured in the supply conduit 12 by the measurement sensor 23 is above or below a predetermined set-point value, so that by means of the control device 25, the actuator 24 and thus the nozzle needle 26 are readjusted such that the set-point temperature is adhered to.

The set point of the temperature can be adjusted with the temperature control circuit with the result that wavelength control of the laser diode 1 is possible, since the radiated wavelength depends on the temperature of the laser diode 1.

If the supply temperature is above the set-point temperature, the adjustable propulsion nozzle 10 is closed, and thus a greater amount of condensate accumulates in the heat exchanger 4, and less steam is withdrawn from the steam network 010.

The discontinuous control device can comprise a two-point temperature governor whereby two difference values of the set point, i.e., temperature, of preferably 20° C. to 35° C., more preferred 25° C. to 35° C. can be set.

The target temperature is preferably a set-point temperature, e.g., as determined by a logic circuit or other suitable mechanism in the temperature controller 390 .

Thus, e.g. the said memory can contain parameters for the starting and finishing values of the set point adjustment range and the connection between the set point and the temperature to be regulated at the location of the measuring sensor, e.g. in the form of a function or characteristic.

Provision may be made here, for example, to evaluate a heat output necessary to adjust a set-point temperature, allowing for an exhaust gas mass flow and the exhaust gas temperature.

Instead of a fixed setpoint of the thermostatic switch 5, the set point of a temperature adjusted on an automatic air conditioning device of the motor vehicle can be used.

In most cases, the switch on pulses will be too long for the required demand of heat and as a consequence the room temperature after the above-mentioned delay time will exceed the set point temperature essentially.

Fever arises when the hypothalamic set point for body temperature is regulated upward, in a manner similar to the workings of a thermostat (Figure 1) .

As a result, the temperature profile in the column 20 is shifted correspondingly so that the difference between the actual temperature in stage 31 M and the set-point temperature for this stage becomes smaller and ideally, becomes zero.

If, on the other hand, the temperature is measured in the laser spot, the set-point temperature must be set so high that the component is sufficiently supplied with laser output regardless of any distortion of the sensor signal towards seemingly higher temperatures.

If, however, based on the above-named method, it is known that a relatively high power is necessary in order to heat the product, since, e.g., a large amount of product is in the pan and/or it has a high heat capacity, or much thermal energy is necessary for the change in temperature, as is the case for thawing, the power output then can be set correspondingly high, in order to assure that the product reaches an aimed-at set-point temperature or state as rapidly as possible.

Subsequently, the reactor temperature can be measured at predetermined time intervals and a deviation of the reactor temperature from the set-point temperature can be determined as control deviation of the first controller.

The method has the effect that as a result of the heat carried into and/or out of the reactor, the reactor temperature can be adjusted to match the set-point temperature of the reactor.

This kind of control is advantageous because it allows a change or deviation from the reactor set-point temperature to be compensated by the comparatively fast and powerful inner heater which is arranged in the reactor itself and—additionally or alternatively—by the more sluggish outer temperature control unit, whereby the error in the measurement result can be reduced and the measurements become more accurate.